برای مشاهده متن به فارسی از مترجم وبلاگ در سمت راست
استفاده کنید.
Background
Photovoltaic solar cells are thin silicon disks that convert sunlight into electricity. These disks act as energy sources for a wide variety of uses, including: calculators and other small devices; telecommunications; rooftop panels on individual houses; and for lighting, pumping, and medical refrigeration for villages in developing countries. Solar cells in the form of large arrays are used to power satellites and, in rare cases, to provide electricity for power plants. When research into electricity began and simple batteries were being made and studied, research into solar electricity followed amazingly quickly. As early as 1839, Antoine-Cesar Becquerel exposed a chemical battery to the sun to see it produce voltage. This first conversion of sunlight to electricity was one percent efficient. That is, one percent of the incoming sunlight was converted into electricity. Willoughby Smith in 1873 discovered that selenium was sensitive to light; in 1877 Adams and Day noted that selenium, when exposed to light, produced an electrical current. Charles Fritts, in the 1880s, also used gold-coated selenium to make the first solar cell, again only one percent efficient. Nevertheless, Fritts considered his cells to be revolutionary. He envisioned free solar energy to be a means of decentralization, predicting that solar cells would replace power plants with individually powered residences.
With Albert Einstein's explanation in 1905 of the photoelectric effect-metal absorbs energy from light and will retain that energy until too much light hits it-hope soared anew that solar electricity at higher efficiencies would become feasible. Little progress was made, however, until research into diodes and transistors yielded the knowledge necessary for Bell scientists Gordon Pearson, Darryl Chapin, and Cal Fuller to produce a silicon solar cell of four percent efficiency in 1954. Further work brought the cell's efficiency up to 15 percent. Solar cells were first used in the rural and isolated city of Americus, Georgia as a power source for a telephone relay system, where it was used successfully for many years. A type of solar cell to fully meet domestic energy needs has not as yet been developed, but solar cells have become successful in providing energy for artificial satellites. Fuel systems and regular batteries were too heavy in a program where every ounce mattered. Solar cells provide more energy per ounce of weight than all other conventional energy sources, and they are cost-effective.
Only few large scale photovoltaic power systems have been set up. Most efforts lean toward providing solar cell technology to remote places that have no other means of sophisticated power. About 50 megawatts are installed each year, yet solar cells provide only about .1 percent of all electricity now being produced. Supporters of solar energy claim that the amount of solar radiation reaching the Earth's surface each year could easily provide all our energy needs several times over, yet solar cells have a long way to go before they fulfill Charles Fritts's dream of free, fully accessible solar electricity.
Raw Materials
The basic component of a solar cell is pure silicon, which is not pure in its natural state.
Pure silicon is derived from such silicon dioxides as quartzite gravel (the purest silica) or crushed quartz. The resulting pure silicon is then doped (treated with) with phosphorous and boron to produce an excess of electrons and a deficiency of electrons respectively to make a semiconductor capable of conducting electricity. The silicon disks are shiny and require an anti-reflective coating, usually titanium dioxide. The solar module consists of the silicon semiconductor surrounded by protective material in a metal frame. The protective material consists of an encapsulant of transparent silicon rubber or butyryl plastic (commonly used in automobile windshields) bonded around the cells, which are then embedded in ethylene vinyl acetate. A polyester film (such as mylar or tedlar) makes up the backing. A glass cover is found on terrestrial arrays, a lightweight plastic cover on satellite arrays. The electronic parts are standard and consist mostly of copper. The frame is either steel or aluminum. Silicon is used as the cement to put it all together.
The Manufacturing Process
1. Purifying the silicon
2. Making single crystal silicon
3. Making silicon wafers
4. Doping
5. Placing electrical contacts
6. The anti-reflective coating
7. Encapsulating the cell
8. Quality Control
To Know About the Manufacturing Process Please Wait.
Coming Soon.
هیچ نظری موجود نیست:
ارسال یک نظر